Control of Noise from HVAC and Interior Machinery (1.2 CEUs)

Course description:

The Control of Noise from HVAC and Interior Machinery course is designed to provide participants with sufficient knowledge of the sound and vibration characteristics of the source noise of HVAC and other interior machinery, which give rise to the unique perception of such noise within buildings. Participants will learn methods of analysis that will enable them to investigate noise problems and to develop solutions to those problems. Note that the design of building structures to attenuate interior sound is NOT covered in this course; that is the subject of another course “Control of Environmental Noise within Building Structures”. Noise control of HVAC installations includes the assessment of noise impact on neighbouring exterior off-property sites as well as building interior noise. Noise control solutions that are available today will be presented. Building Code requirements and good practice guidelines will be discussed.

This course assumes a familiarity with principles and nomenclature of sound, with some basic knowledge or experience with sound propagation in building structures. It describes the characteristics of the source noise of machinery, primarily HVAC, as installed in the interior of buildings and discusses industry-standard testing procedures that are used for problem investigation. This course can provide information about some methods of analysis that can lead to identification and correction of machinery noise problems.

Course objective:

The participants will achieve the expertise primarily needed to investigate interior noise problems caused by HVAC and other building machinery. Measurement in as-built structures in accordance with industry-accepted procedures will be described to undertake problem investigations. Analysis methods of measured data that could lead to problem definition will be discussed. This would enable participants to provide in-house capabilities for noise analysis in consulting firms, and possible extension to external consulting after sufficient experience had been obtained.

Target audience:

Engineers and architects who are interested in increasing their range of knowledge relating to practical noise control; Consulting engineers who are considering broadening their practice; Engineering consultant companies who want to establish a capability within their staff for designing and investigating interior building machinery noise.

After you attend this course you will be able to:

Select commonly-used and tested building machinery to achieve Code-compliant or acceptable good practice interior noise reduction in buildings. Use supplied or available data bases of these components and adjust or supplement the bases with additional or modified data as required by the noise control scenario. Understand testing procedures and available instruments for problem investigation. Recognize analysis methods that can isolate the identity of the source noise and offer possible solutions to reduce or remove the noise impact.

 

Neil Standen

Mr. Neil M. Standen, PEng, BASc, MEng, currently retiring President of Urban Aerodynamics Ltd. Member (2009), Working Group 41, ANSI Standard 12: Guidelines for Developing a Community Noise Ordinance or Regulation; Director, Founding Board of Juno Beach Centre, Normandy, France.

Thirty years as President of Urban Aerodynamics Ltd consultancy; ten years with Morrison Hershfield Ltd (Ottawa); twelve years with Transport Canada, ten as Chief, Aeronautical Environmental Technology Development; six years with Low Speed Aerodynamics Laboratory, National Research Council; three years with Boeing Airplane Company (Seattle, USA).

Noise Consultant to Dept. of National Defense regarding Air Force Bases, NATO Training Range at Goose Bay, Arctic Forward Operating Bases and NATO Noise Programs. Noise Consultant to Canadian Airlines Association, Winnipeg International Airport, Victoria International Airport Vancouver International Airport, Grantley-Adams Airport (Barbados) and many regional airports in Canada. Noise Consultant to Residential development companies (Minto, Richcraft, Domicile and others) in Ottawa.

Publications in Journal of Sound and Vibration; Journal of the Acoustical Society of America; Journal of Applied Ecology.

Program Outline:
1. Noise Problem Identification: (Sessions 1 through 3; 4.5 hours) Spectrum Measurements, Narrow Band Frequency Tonal Components, Hydro-frequency versus Rotating Machinery Signals; Room Effects/Resonances
2. Air-Handling Machinery Installed in Buildings: (Sessions 4 through 5; 3 hours) HVAC Outdoor & Indoor Noise; Fan Noise & Air Duct Noise Characteristics; Standards of Acceptability
3. Attenuation of Noise in Air and Water Systems: (Sessions 6 through 8; 4.5 hours)Reactive Attenuation in Ducts; Dissipative Attenuation; Turbulence Noise Sources in Ducts and Piping; Water Hammer; Attenuation of Noise Through Duct and Pipe Walls; Vibration Isolation

GIC reserves the right to cancel or change the date or location of its events. GIC's responsibility will, under no circumstances, exceed the amount of the fee collected. GIC is not responsible for the purchase of non-refundable travel arrangements or accommodations or the cancellation/change fees associated with cancelling them. Please call to confirm that the course is running before confirming travel arrangements and accommodations. Please click here for complete policies.

Education @ Your Desk. A Live Webinar Class means that you will attend the class via the web using your computer. There are scheduled breaks for coffee and lunch. You use a microphone, headset, or your phone and are able to interact with the instructor and other students while following notes while watching the presentation slides online just as you would in a live classroom. Notes are posted online. For an extra cost a hard copy can be requested.

The virtual classroom is becoming more and more popular, and we have a lot of experience teaching in this format. The only real difference between a live in-class and live via webinar is where you sit and what you look at. You can learn from the comfort of your own home or office. You pay less for the live webinar format than you would for the in-class format, and you do not have to travel to another city to attend the class. Please contact us at gic@gic-edu.com for Special Group & Corporate Rates for one or more participants.

We could offer any of our courses at a location of your choice and customized contents according to your needs, please contact us at : inhouse@gic-edu.com or click here  to submit an online request.

PC-based attendees
OS: Windows XP, 2003 Server, Vista, 7, 8
Browser:
Internet Explorer 7.0 or newer
Mozilla Firefox 4.0 or newer
Google Chrome 5.0 or newer

Macintosh based attendees
OS: Mac OS X 10.6 (Snow Leopard), 10.7 (Lion), 10.8 (Mountain Lion) or newer
Browser:
Safari 3.0 or newer
Mozilla Firefox 4.0 or newer
Google Chrome 5.0 or newer

iOS
Device:
iPad 1 or newer, iPhone 3GS or newer, iPod Touch (3rd generation) or newer
OS: iOS 6 or newer

Android
OS: Android 2.2 or higher


Course Materials

Each participant will receive a complete set of course notes and handouts that will serve as informative references.

Need a Government Grant?

Jumpstart your training with the help of Global Innovative Campus (GIC-Canada) & the Canada Job Grant.

Seminars and Workshops offered within your organization anywhere in the world.

Offline Registration

To Register by fax, download and fill our registration form, then fax it to (888) 849-4871. Mail your cheque to our address.

If you have a question regarding this course, please click here to contact us.
Share
CEUs Certificate

A certificate of completed Continuing Education Units (CEUs) will be granted at the end of this course. A fee is required for all complimentary webinars.

On-Site Training

This course can be customized and delivered on-site at your facility.

Stay on top of your profession development with useful articles and industry updates Subscribe